SPECIAL TOOLS PAGE 4

 Item 3424 

Spreader Socket 

Steering Knuckle Strut Clamp Spreader

Tool is for safely opening the pinch spindle to separate the steering knuckle from the shock/strut.

Spreader Socket Tool for A4 platform including Golf Jetta and Gti 337 20a.e. GTI 1999 to present. 

This tool is needed any time the strut needs to be separated from the wheel bearing housing. 

Most common would be changing/replacing struts, coil spring, or the entire strut assembly. 

You would also use this tool when servicing the wheel bearing. You can not easily remove strut from wheel bearing housing without it. The wheel bearing housing clamps down very tight on the strut assembly-even with the bolt removed the housing is still firmly clamped to the strut. This socket allows you to spread the housing where it's clamped on so the strut can be removed. 

Basically this tool is a must any time the strut/wheel bearing housing needs to be removed. 

Important Note: Late model pinch bolts may need a 14mm (XZN) socket tool (not included).

Item GM2701

 Four Piece Set (4) Aapplication-specific puller tools designed especially for installation and removal of ignition coils. Applicable Audi VW with direct ignition engines.

Prevents damage to ignition coils, allowing quick removal. 

See details below...

#0282 same as T10094a - used for removal and fitting of ignition coils with final output stage. Used on 8-cyl. (W8) and 12-cyl.

 (W12 injection engines)

#0285 same as T10095a for removing and assembly of ignition coils with final output stage. 2.8-liter, vr6, 4-valve engines

#0283 same as T10166 for removal and fitting of ignition coils with final output stage. Used on 8-cyl. (W8) and 12-cyl. 

(W12 injection engines)

#0284 same as T40039 for removal and assembly of ignition coils with final output stage. Engine codes (AWA,ASN,BBK).

 Item MK-AWV8 

Big-mouth wrench with extra-wide opening jaws and short handle for access in confined areas. 

     Extra-wide opening jaws with shorter handle for maximum access in confined areas

    True ergo design, with thermoplastic handle and larger grip width

    This 8-inch wrench tool is ideal for plumbers, electricians, and maintenance workers

    Slim head with tapered jaws combine easy accessibility with extra turning strength

    Perfect for under the sink, within enclosures, or anywhere that a short handle is needed

This 8-inch wrench tool is ideal for Auto Technicians, 

backyard mechanics, plumbers, electricians, and maintenance workers 

    Thin Jaw Wide Mouth - 45% wider opening and 45% thinner jaw

    Length (Inches) : 8

    Maximum Jaw Opening (Inches) : 1 1/2

    Head Thickness (Inches) : 11/64

    Jaw Tip Thickness (Inches) : 1/4

Item 68950 

32mm impact socket designed to help the technician remove & install axle nuts 

on VW Audi and BMW etc.  

 High Quality tool to remove and install 12-point axle nuts. The  forged 12-point 32mm socket with 1/2" drive is one of the the strongest sockets in the industry that will do the job every time. Pictures are for reference only. 

Does not come with ratchet. This sale is for one socket only.

 5pc Magnetic Pentagon Head Bit Set 

5 sided Security Screwdriver Bits 1/4 drive

These are Security (Tamper Proof) Pentagonal-Drive Bits

Five-sided "Penta" Drive Bit Set includes sizes H3/H4.3/H6.7/ H7/ H7.6  for a wide variety of applications, length 50mm magnetic, Tamper Proof security head can quickly and efficiently grab the screws, preventing them from dropping  and slipping, providing more work efficiency.   

Item 386626

Unique "Mighty Worm" magnet pickup tool

bends, shapes and flexes to fit into any corner or crevice. 

This tool is 26 inches long. Picks up to 10 ounces

Extremely small magnetic head, barely 5mm in dia.

The head is mounted on an extremely flexible 26" long copper wire. 

The Mighty Worm can reach places others cannot!  The Mighty Worm Magnetic Pickup Tool is extremely useful in picking up parts in small gaps and confined spaces 

such as: deep inside car doors, under car seats, small gaps in the engine compartment, 

holes and gaps in other parts of the car body etc. 

 Item M36MFBL 

Double sided socket - fits many 24/36mm filter applications

Double sided socket includes 

24mm 6-point and 36mm 6-point sides

Oil Filter Socket Reversible Fuel Filter Cap Remover and Installer 

Compatible with 6.0L / 6.4L Ford Power-stroke Diesel 2003-2010 (blue) 

The fuel filter sleeve is reversible 24mm / 36mm. The main fuel filter cover is 36mm, 

and the secondary fuel filter cover is 24mm. 

Note: On 6.4L Applications, all filters use the 36mm end of the socket

MK7BA7

7 Piece Ball End Screwdriver Bits Set

Overall length: 2.55 inch (65mm)

Ball End Hexagon, shank: 6.35mm/ 1/4-inch Hex Shank

Ball End Hexagon Head 

Size: H2.5, H3, H4, H5, H6 Magnetic

Ideal with power tools for screwdrivers,  air drills etc

Made of S2 alloy steel for long life

MK747SH

Multi-tool Sheath For Belt, Leather EDC Pocket Organizer W Pen Holder

Size: 7.09 x 5.31 inch.

Flashlight known to fit up to 0.91 inch diameter flashlights

Accepts normal sized key rings

Flashlight Pocket-9.5cm X 3.5cm; Pen Pocket-9.5 cm X 2.5cm; Multitool Pocket-11cm X 5.3cm

(multi tools not included).

MK747X15

15mm Hinge Pin Tool for Mercruiser Mercury boat.

VERY  RARE 15MM SPECIAL SOCKET TOOL 12 POINT XZN STYLE 

Note: This tool measures 14.5mm from point to point (outer diameter). 

Hinge Pin Tool fits the screws on bell housing for Mercruiser Alpha One Gen I or Gen II  drives, and all Mercruiser Bravo drivers. This tool is specifically manufactured for a perfect fit. 

Overall length of this tool  is 2 inches and the drive size end is 1/2 inch. 

MK2626P

Special Pin Wrench helps you adjust the timing belt tension/fix the tension pulley.

This tool will allow you to accurately apply the correct preload to the eccentric timing belt tensioner pulley with the engine mounted in the vehicle. Adjust with a 1/4" drive ratchet

Note: this tool also helps to remove the outer CV joint on most front-wheel drive vehicles with a concealed internal circlip. Fits for Dodge, Eagle, Mitsubishi vehicles equipped with Mitsubishi built engines. ie. Dodge, Mitsubishi, Eagle, Plymouth, Hyundai, Kia, Chrysler.

OEM ref number MD998767

MK10MMRB

Ribe Socket size 10mm rare and hard to find. Ribe tools are often used in body connecting bolts and sometimes found on old brake assemblies. This sale is for size 10mm only. This tool is not a  Polydrive or Torx,  it is called Ribe and the pattern will vary slightly from a Polydrive. 

Heavy duty 1/2 Drive with Bit made of S2 Steel!

This tool is 5.5 inches long  overall. Not intended for use with an impact use.

 Ribe are sometimes used Italian cars, Fiat, Lancia, Alfa Romeo etc. 

Volkswagen Audi headbolts are not Ribe, they are called Polydrive. 

MKLSP1

 All New Seal Puller 

Works better than all other pullers available  on the market for import car lip seals. Works best on front cam and  crank seals. Has no moving part to adjust, making seal removal a snap.  Slim, ergonomic design fits into tight areas. Will not damage shaft  journals or seal housings if used properly. Most pullers available  either require adjustments to set the tool up, or are just too large to  fit into the seal lip without risk of damaging the shaft journal, and  some will just not fit into the work area, period! Why spend extra time  fighting the seal and the tool, with this NEW seal puller, front engine  seals become a snap. Stainless Steel Blade / 2 Component Handle

TESTIMONIAL: We have used this product  for three years. Our mechanics swear by this tool, and prefer it to all  others pullers on the market. The Puller is slim and the unique design  makes pulling even the most difficult to access seals a snap, (V6 Camry  lip seals, anyone?). Combine this tool with a dousing of silicone spray and the seals just pop tight out of the engine. 

L. Farnsworth . 

ITEM 30709

9" Ratcheting Slide Wrench       

Multiple sizes in one tool - adjusts from 5/16 (8mm) to 1 inch  (25mm)

Pivoting flex head locks into position for 180º of flexibility

Ratchets for quick removing and tightening

Knurled thumb wheel adjusts  sizes easily

Heavy duty chrome molybdenum construction

Low profile head  for tight spaces & Meets or exceed ANSI for torque.

ITEM 30789

UNIVERSAL

DOUBLE BOX WRENCH

  Self-Tightening universal box wrench features a total of 18 tapered openings to fit a wide range of fastener sizes and styles. Corrosion resistant chrome plating with mirror polish finish, is durable and easy to clean

Fits standard hex head fasteners from 5/16 inch to 7/8 inch and 8mm to 22mm in diameter.Unique open-end design also fits eye-bolts, hooks, J-bolts, cup hooks, wing nuts, square end fasteners up to 1.5 in (38mm) long .

Low profile, extended length pattern allows for maximum torque, in tight space. Excellent go-to tool for home improvement, construction,  carpentry, automotive, recreational vehicles, general repair, and  maintenance. 

Total length: 10-3/4" (270mm); 5/16" (8mm) profile

ITEM 90266

Ultimate 12 pc. Needle File Fold-up Set Auto Tools

    Needle File Fold-up Set Auto Tools

    12 Files all in One set!

    For precision filing delicate parts. 

ITEM U45-SET

 45° UNIVERSAL JOINT SET

3 PIECE SET COMES IN 1/4″, 3/8″ &  1/2″ DRIVE 

The 45 degree Universal Joint Combines High Torque, Smooth Rotation & A Profile That Offers Maximum Workspace Accessibility.  You get all three sizes with this purchase. 

ITEM HN4033

Holder plus extension Pins

Timing Indicator Set includes holder plus extension pins (2)

This set is for someone who already owns a Dial Indicator (not included).

 Includes M8, M10, and M12 adapters. For use on diesel injection systems  especially on engines: DE, MD, ME, MF, 1V, 1Z, AAB, AAZ, ACV, AHU, ALH,  AWP, AWV, CS, CY. Note: this set will work in place of Volks tool 2066  Specifications The two main pieces are approx. 8 x 1.0mm The black  adapter is 10 x 1.0 The silver adapter is 12 x 1.25