Special Tools Page 3

NUMBER MK-114180

Long "Turned-Down" Socket with Torx End

MADE IN U.S.A.

Features Machined Shaft to Allow Proper Clearance to Service Dual Mass Flywheel Mount Bolts, as They are Off-Center to the Access Point, Especially from Wear

Why is this tool needed?

The flywheel bolts on many BMW engines (especially older V8 models like M60, M62, S62, and some others) are positioned in tight/recessed spots behind the engine/transmission bell-housing.

A standard/short Torx bit or socket won't reach them properly without risking damage to the tool, bolt, or surrounding components (or it simply can't fit due to the depth and angle). This extended socket provides the necessary reach and strength to torque those bolts correctly during jobs such as:

Clutch replacement (manual transmission vehicles)

Dual-mass flywheel (DMF/ZMS) replacement

Transmission removal/installation

Crankshaft-related work where the flywheel needs to be removed or held,

It's particularly common on 1990s–early 2000s BMW models like the E34/E39 540i, E38 740i, E39 M5, E46 M3 (in some cases), and other V8-powered cars with manual gearboxes.

Services E34 and E39 with the 4, 4.4 and 5 Liter with Standard Transmission and Manual Transmission, Including 530I with Dual Mass Flywheel (1993-1995), 540I with Dual Mass Flywheel (1993-2003)

Also Ford 3.5 Liter V6 Found in the Edge

Also for some Lincoln Mkx and Mazda Cx-9 Rear Bearing Assembly Mounting Bolts, as Shaved-Down Design Allows Clearance of the ABS Tone Ring.

NUMBER 21139

2-PC WHEEL ALIGNMENT PINS (4 sizes)

Wheel stud alignment guides are used when mounting or dismounting wheels, especially those models featuring lug bolts instead of lug nuts.

Fits most BMW, Chrysler, Ferrari, Fiat, Ford, GM, Hyundai, Land Rover, Lamborghini, Opel, Mercedes, Renault, Saab, Seat, Vauxhall, and Volvo vehicles.

Each end has size markings stamped for easy identification

Applications:

M12 x 1.25mm: Alfa Romeo, Chrysler, Dodge, Fiat

M12 x 1.5mm: VW Audi, BMW, Benz, Mini Cooper Porsche, Vauxhall, Volvo,

M14 x 1.25mm: BMW, Mini Cooper

M14 x 1.5mm: Some Audi, Alfa Romeo, BMW, Citroen, Chrysler, Ferrari, Fiat, Ford, GM, Hyundai, Land Rover, Lamborghini, Opel, Mercedes-Benz, Peugeot, Porsche, Renault, Rover, Saab, Seat, Skoda, Vauxhall, Volvo, Volkswagen.

NUMBER 86109-00

Low Profile Hex Set

5-Piece Set Includes:

2.5 mm, 3 mm, 4 mm, 5 mm, 6 mm Hex Keys

Low profile design feature 3/8 inch (10mm) clearance, and a 15 degree offset angle for improved access for hard to reach fasteners;Corrosion resistant heat treated steel handles with durable S2 alloy steel bits; Includes key ring & carabiner clip for ;Includes Great for everyday projects at home, garage, shop and office such as automotive fasteners, electronics, home appliances, equipment and more.

Includes key ring & carabiner clip for convenient organization and compact storage.

Popular set for mechanics, DIYers, and anyone needing hex tools in cramped spots — very handy and pocket-friendly!

NUMBER 36554

ADJUSTABLE PIN WRENCH

Remove and replace wheels on angle grinders with this adjustable pin spanner wrench.

Adjustable Lock-nut Grinder Wrench designed specifically for easy installation and removal of discs, abrasive wheels, wire wheels, backing pads, lock nuts, and other attachments on angle grinders. This tool functions as an adjustable pin spanner wrench (also called an adjustable pin wrench or hook spanner in some contexts).

It features two adjustable pins that fit into the holes or slots on the grinder's flange, arbor nut, or spanner flats, allowing you to securely hold or turn the component while using the grinder's spindle lock (or another wrench) on the opposite side.

Heat-treated carbon steel body for strength and durability; often with a PVC-dipped or rubberized handle for comfort and non-slip use.

Fits grinder hubs from 3/8" - 1-1/16" in size, and over all size: 7-1/2" with a Adjustable Knobs. Ideal replacement pin wrench for most angle grinders, bench grinders, mitre saws and circular saws. Exact fit for most top name brands (Makita, Dewalt, Bosch, Hitachi, Milwaukee, Metabo).

NUMBER 9814-00

SET 3 TERMINAL TOOLS

For the removal of VAG and Porsche connectors

Connectors are found on MAF sensors, coil packs, headlights, fog lights, level sensors, map sensors, etc. Comfort grip handle for easy use.

Direct fit onto push & pull connectors.

Applications: VAG - VW, Audi, Skoda, SEAT, Bentley & Porsche

Kit Includes

9812K & 9812E - Disconnect tools are designed for removing wires in VAG connectors. Use for inserting into the front of the connector and pushing lock pins down allowing removal of the wire.

1034 - T-handle tool fits directly on push & pull style VAG connectors and provides the perfect amount of leverage to release the connector without breaking tab.

NUMBER MK-PT3747

Hose Remover Tool Set

Radiator hose removal hooks (also called hose removal picks or hook tools), automotive specialty tools specifically designed to help separate stuck rubber hoses—like radiator, heater, coolant, or transmission hoses—from fittings without damaging them. The curved hook slides between the hose and fitting to pry or pull it loose, while the angled/right-angle hook works well in tighter spaces or for leverage on different hose configurations and are a must-have for mechanics dealing with old, swollen, or clamped hoses that are tough to remove by hand.

They can also double as general hook/pick tools for removing O-rings, seals, or small clips, but the primary design here is for hose removal.

NUMBER 1701T2

Long Thin wrench Set

32mm and 36mm

This special wrench set is often used to remove and install fan clutch nut and assemblies when replacing water pumps or doing other engine services.

Designed for confined areas when removing many fan clutches.

The slim design lets wrench fit into tight areas, and the extra-long length is ideal for fan shroud clearance.

Especially for VW, BMW, Mercedes and Porsche.

Ford & GM vehicles Land Rover (Discovery 2)

Overall length 15 inches

Each tool is 1/4 inch thick.

NUMBER MK2626

Special Pin Wrench

This tool helps you adjust the timing belt tension/fix the tension pulley.

This tool will allow you to accurately apply the correct preload to the eccentric timing belt tension pulley with the engine mounted in the vehicle.

Accurately rotates and tensions the eccentric timing belt tension pulley to set proper belt preload during timing belt replacement or adjustment. Insert the pins into the pulley's holes, with a 1/4" drive ratchet for controlled turning.

Additional Use: Helps remove the outer CV joint on many front-wheel-drive vehicles by engaging concealed internal cir-clips (snap rings).

Compatibility:

Fits vehicles with Mitsubishi-built engines, including:Dodge (e.g., Stealth 3.0L DOHC, Colt, various models with Mitsubishi engines)

Eagle (e.g., Summit)

Mitsubishi (e.g., models with 2.4L I4, 3.0L V6 like 3000GT/Stealth equivalents)

Plymouth, Hyundai, Kia, and Chrysler references where Mitsubishi engines were used (common in 1980s–1990s joint ventures like Diamond-Star Motors).

Works on many injected Mitsubishi engines, including 4G63 variants (e.g., in Evo/DSM platforms) and others up to more recent models in some cases.

Black cast/heat-treated steel body, pin spacing fixed to match the tensioner pulley's holes, square 1/4" drive recess on top for ratchet attachment. Compact tool for tight engine bay access.

OEM Reference: Chrysler/Mitsubishi MD998767 (or equivalents).

NUMBER MK-245

Pin Wrench Spanner Tool

Rear Spoiler 996 Turbo + 997.1 Turbo/GT2 + 997.2 Turbo/S/GT2

Do you need to remove the rear spoiler from your 996 or 997 Turbo? If so, you will need this special release tool to do the job.

Special Tool overall length is approximately 170mm (6-1/2") and 5mm thick.

Pin wrench makes removal of the wing from the stock hydraulic rams easy.

Engaging the pin through the outer cylinder and grasping the inner slotted element is necessary(make sure the holes in the outer and inner cylinder are lined up and the pin keeps them together while turning).

Turn about 90 degrees clockwise to release, 90 degrees counterclockwise to lock

This tool is a must for 997 turbo wing removal (the factory used a thread locker).

FYI: Some people will wrap the wrench with tape so it doesn't scratch the piston, or some people will coat the tool with "Plasti Dip". Plasti Dip is a durable impact, and abrasion resistant Rubber coating (not included).

Note: This tool may or may not come with a rubber handle, depending on stock level at time of shipment.

NUMBER 4491-DP

Rare Thin Wall 22mm deep cut-away Socket

Dont risk damage to your injectors using a regular socket. This tool will make it a breeze to remove your injectors. It will allow you to get the injectors out with the short tails of injector return lines still attached. Made with chrome vanadium for extra strength and durability.

Application Engine 1.Mercedes OM606 engine 1995 E300D 124.131 3.0 L6 DIESEL 606.910 1996 E300D 210.020 3.0 L6 DIESEL 606.912 1997 E300D 210.020 3.0 L6 DIESEL 606.912 1998 E300D 210.025 3.0 L6 DIESEL 606.962 1999 E300D 210.025 3.0 L6 DIESEL 606.962 2.Mercedes-Benz OM605 engine 97–1998 W210 E 250 Turbodiesel 1995–2001 W202 C 250 Turbodiesel 1996–1998 W210 E 250 D 1993–1996 W124 E 250 D 1993–1995 W202 C 250 D 3.Mercedes-Benz OM604 engine 1996–1998 W210 E 200 D 1996–1998 W202 C 200 D 1996–1998 W210 E 220 D taxis 1995–1998 W210 E 220 D 1996–1998 W202 C 220 D taxis 1996–1998 W210 E 200 D

NUMBER 13410

Steel wire brush

Designed specifically for cleaning brake calipers during brake pad replacement.

Similar to the Mercedes number 000 589 26 68 00 printed on it.

The angled, narrow head with stiff steel wires allows it to reach into tight spaces on brake calipers to remove built-up brake dust, rust, and old lining deposits without damaging sensitive components like pistons or seals. The ergonomic red plastic handle provides a good grip. These brushes were developed in cooperation with the automotive industry (particularly for Mercedes-Benz service) and are commonly used by mechanics when servicing brakes. Similar versions exist in stainless steel (often with black or green handles) or brass for different surfaces.

Email for availability.

NUMBER 95214

4-Piece Nylon Pry Kit

Made of strong nylon (a type of tough, durable plastic).

Nylon is specifically chosen for these auto trim removal tools because it's rigid yet non-marring —

it won't scratch or gouge painted surfaces, leather, vinyl upholstery, or plastic panels in your car. automotive trim removal tools (often called nylon pry bars or "non-marring" pry bars).

While these look like standard workshop tools, they are specifically designed for delicate work where you need to apply force without scratching or denting the surface.

Primary Uses

Interior Trim: Removing plastic dashboard panels, door cards, and center console covers without leaving marks on the plastic or leather.

Electronic Clips: Popping out fragile plastic clips and fasteners that hold wires or panels in place.

Exterior Moldings: Prying off emblems, chrome trim, or weather stripping without damaging the vehicle's paint.

Car Audio: Removing head units (radios) and speaker grill.

NUMBER 83199

2-piece Plastic Chisel Set

Manufactured by Wilmar LLC (under their Performance Tool brand).

Designed for safely removing decals, stickers,

adhesives, emblems, molding, and similar materials without scratching or damaging underlying surfaces (like paint on vehicles). The chisels are made from impact-resistant plastic.

Use to remove decals, stickers, and moldings from your vehicle without damage to the finish

Made of high-impact plastic to withstand mallet strikes

Handles incorporate a hand guard for added protection

Tips can be sharpened with a second cut or smooth cut file to prolong tool use

One 1-In width chisel, one 1/2-In width chisel

NUMBER VW20500

Fuel line disconnect Plier allow for faster removal and replacement of connections on fuel lines without damaging the connectors.

The handle of these pliers is ergonomically designed, providing an anti-slip and comfortable grip, saving time and effort.

The fuel pipe pliers are easy to operate. Use the pliers to pull the connector backward to easily connect or disconnect the fuel line or plug

of the injector. Size is approximately 8.86 x 3.98 inches, suitable for most vehicles, please confirm your size needed before purchasing to ensure that the product is suitable for your vehicle.

Pictures are for reference only.

NUMBER 2636A

17-blade mini feeler gauge set.

This is a compact automotive/mechanic's tool designed for measuring small gaps, clearances, or thicknesses—commonly used for valve adjustments, spark plug gaps, ignition points, or general precision fitting in engines and machinery.

Number of blades: 17

Blade dimensions: Each blade measures approximately 1-3/4" long × 1/4" wide (mini/compact size for tight spaces)

Thicknesses (in inches, SAE): .010, .012, .013, .015, .016, .017, .018, .019, .020, .022, .024, .025, .026, .028, .030, .032, .035

The blades are straight (non-offset), fold into a protective handle/case, and are made for durability (hardened steel with etched markings).

It's a specialized "mini" version for easier access in confined areas.

NUMBER MK1185

Carburetor Adjustment Set

6-Piece Small Engine Carburetor Adjustment Set.

This is a specialized tool kit designed for tuning and adjusting carburetors on 2-cycle small engines, commonly found in chainsaws, string trimmers, leaf blowers, hedge trimmers, and other outdoor power equipment. It helps technicians make precise idle speed, high-speed, and low-speed mixture adjustments to keep engines running efficiently and in compliance with EPA emissions standards.

Key Features6 common adjustment tips in one ergonomic handle set with a comfortable grip, chrome-plated shafts for durability, with black/red handles.

21-Tooth Spline

7-Tooth Spline

Single D

Double D

Pac Man (a half-moon or notched shape)

4mm Hexagon