MK-91107
91107
Belt Gauge provides a simple and quick way to measure belt tension on V-belts to
ensure long belt life and optimal belt drive performance. Easy to use gauge
designed to tension all automotive V-belts up to, and including 7/8 in. top widths
Scale reads in pounds and kilograms
Measures tension from 30 to 160 lb., and 15 to 75 kg.
Die-cast aluminum body, nylon indicator arm and pressure pad
Note: Not for use on timing belts
Timing Set 44233
44233
Timing tool Set is used to rotate and align the crankshaft and camshaft.
Appl: Porsche 987, 981, 997, 991 flat engine.
Ref OEM numbers: 9772, 9773.
Flywheel Lock MK-91FWL
MK-91FWL
Flywheel Lock 911 (991) For assembly measures on engine/flywheel/clutch,
designed for counter-holding the flywheel during removal and installation of the engine
48mm (1-7/8") long.
Porsche Boxster after March 2012,
911 Carrrera starting December 2011
Wheel Sockets 45611
45611
SET 20 PCS WHEEL SCREW LOCK SOCKETS
Set for installing and removing locks of many VAG and Porsche models.
Contents: #50, #51 , #52, #53, #54, #55, #56, #57,
#58, #59, #60, #61 , #62, #63, #64, #65, #66, #67, #68, #69.
OEM Set Reference number: T10190
Wrench MK-3217
MK-3217
VW Audi Fuel Sender Wrench 1/2 inch Drive
Removes and installs 139mm fuel gauge sending unit retainer nut.
Applicable: VW VR6 Engine, Audi A4 and A6 models & Porsche 996 and 986
Spring Clips VW171
VW171
Set (2) Spring Clips
Two tools for securing cam followers within crank case half during assembly.
Fits: Porsche 914-4 1.8 (1974-1975) 1.8L, Porsche 914-4 2.0 (1973-1976) 2.0L,
Porsche 912 (1965-1969) 1.6L, Porsche 356A (1956-1959), Porsche 912E (1976) 2.0L,
Porsche 356C/SC (1964-1965), Porsche 356B (1960-1963)
All VW air-cooled engines.
Float Gauge Kit P226K
P226K
Float Gauge Kit
Measures the float bowl fuel level when using Weber or Zenith 3 barrel carburetors.
The gauge is designed to check float levels with the engine running.
Comes with instructions and adjustment washers.
*This item is on backorder
XZN116MH
XZN116MH
This is size M16 Tamper-proof style Transmission Drain Plug Socket
Similar to OEM number 3357
XZN 16mm Triple-square (12 POINT) Socket
3/8 Drive. Tool is used on Transmissions that have a tamper-proof drain plug.
Only 1.5 inches long for working in confined areas.
Airbag Set 4719TN
4719TN
7 Pc Airbag removal tools used to remove drivers airbag from steering wheel
1999-04 new body style Passat, jetta, golf and beetle. Passat b5, polo, lupo,
AUDI, A4 and A6, SKODA superb. Golf 4, new beetle, SEAT, Golf 4(BJ. 1998-2004),
VW-passat AB BJ. 1997, bora AB BJ. 1999.
Multi-Spline Socket 3400
3400 Multi-Spline socket
Special tool same as Porsche number 2592
Tool required to remove and replace the free spinning alternator pulley
Appl: VW 1994 and newer, Golf III, Vento, Passat,
Audi A3, TT, and Porsche Boxster
VAG ref number is 3400.
Comparable to Mercedes #602 589 00 10 00
Comparable to Volvo #9995760
Socket 67344
67344
Center lock wheel nut socket is designed to remove or install
center-lock wheels, saving time and labor.
3/4" drive tightening torque, maximum 369 ft/lbs (500 Nm).
Do not use with impact ratchet impact gun or impact wrench!
Made of high grade Aluminum, with black finish
Applicable Porsche 991, for Cayman, for Panamera
Deep Socket 4491-D
4491-D
Rare Thin Wall 22mm deep cut-away socket is custom designed to allow for
the easy removal and installation of the complete Volkswagen strut assembly.
It makes the job easier by holding the nut while the strut shaft is turned with an allen wrench. 1/2 inch drive.
Feeler Gauge Set P2133
P2133
Feeler Guage Holder for Porsche 911
Needed for correct adjustment of valve clearance.
designed specifically for the air cooled Porsche engine.
Unlike normal feeler gauges, this tool has a specially contoured shape
that allows you to measure the gap deep inside the recess of the valvetrain.
Comes as shown with .004 inch (0.10mm) replaceable blade.
4491-18TN
4491-18TN
Special Open-sidewall Deep socket 18mm used secure shocks and struts to their mounts. Designed to remove or install the locking nut on the front suspension strut. Length: 82 mm
Available in 5 different sizes: 18mm, 19mm, 21mm, 22mm and 24mm
Terminal Tool 45066
45066
Terminal Tool-Connector Removal Tool
For removal of many VAG and Porsche push & pull connectors, fits directly onto the push and pull connectors.
2.Used with MAF sensors, coil packs, headlights/fog lights, level sensors, MAP sensors etc. For: VAG VW AUDI Porsche
Size: 93 X 80mm
Puller Tool 6789TN
6789TN Puller tool same as old number 3032
Designed for camshaft sprocket pulley removal on VAG Applicable: 6-cyl. TDI Common Rail, 2.7L TDI common rail engine and 3.0L TDI common rail engine.
AUDI Q5/ A5/ A4/ Q7/ A6, Porsche Cayenne, VW Phaeton.
Ref new number T10320 .